Photo credit:  Jack Clark, Surface Analytics LLC, jclark@surfaceanalytics.com and SME (formerly Society of Manufacturing Engineers)  To see the original full size document download the pdf from: https://www.slideshare.net/dryfinish/surface-finishing-3-d-printed-metal-parts-profilomic-and-areal-data

Centrifugal Isotropic Finishing has been shown to be useful in reducing the rough surfaces common to 3D printed parts.  Below is an example of surface finishes that can be achieved with the method.  The slides provide profilomic and areal data tabulated by Jack Clark, President of Surface Analytics.  This work was performed by Jack for a study being made by SME’s Machining/Material Removal Technical Community.  The slides show surface readings from a part pictured above as printed, and then following centrifugal isotropic finishing.  The measurements were made in both 2D and 3D.  To summarize, in this test, surface roughness was reduced from 356.24µin Ra. to 12.06µin Ra.

Slide1Slide2Slide3Slide4Slide5

additive-manufacturing-image-1
ABOVE: Before and after example of centrifugal isofinishing on 3D printed aerospace turbine engine blades

Centrifugal isotropic finishing

Centrifugal isotropic finishing (CIF) is a high-energy finishing method, which has come into widespread acceptance in the last 25-30 years. Although not nearly as universal in application as vibratory finishing, a long list of important CIF applications for precision parts have been developed in the last few years.

Similar in some respects to barrel finishing, in that a drum-type container is partially filled with media and set in motion to create a sliding action of the contents, CBF is different from other finishing methods in some significant ways. Among these are the high pressures developed in terms of media contact with parts, the unique sliding action induced by rotational and centrifugal forces, and accelerated abrading or finishing action. As is true with other high energy processes, because time cycles are much abbreviated, surface finishes can be developed in minutes, which might tie up conventional equipment for many hours.

barfunc
Centrifugal Barrel Finishing principles – high-intensity finishing is performed with barrels mounted on the periphery of a turret. The turret rotates providing the bulk of the centrifugal action, the barrels counter-rotate to provide the sliding abrasive action on parts.

The principle behind CIF is relatively straightforward. Opposing barrels or drums are positioned circumferentially on a turret. (Most systems have either two or four barrels mounted on the turret; some manufacturers favor a vertical and others a horizontal orientation for the turret.) As the turret rotates at high speed, the barrels are counter rotated, creating very high G-forces or pressures, as well as considerable media sliding action within the drums. Pressures as high as 50 Gs have been claimed for some equipment. The more standard equipment types range in size from 1 ft3 (30 L) to 10 ft3, although much larger equipment has been built for some applications.

Media used in these types of processes tend to be a great deal smaller than the common sizes chosen for barrel and vibratory processes. The smaller media, in such a high-pressure environment, are capable of performing much more work than would be the case in lower energy equipment. They also enhance access to all areas of the part and contribute to the ability of the equipment to develop very fine finishes. In addition to the ability to produce meaningful surface finish effects rapidly, and to produce fine finishes, CBF has the ability to impart compressive stress into critical parts that require extended metal fatigue resistance. Small and more delicate parts can also be processed with confidence, as the unique sliding action of the process seems to hold parts in position relative to each other, and there is generally little difficulty experienced with part impingement. Dry process media can be used in certain types of equipment and is useful for light deburring, polishing, and producing very refined isotropic super-finishes.

Below: Centrifugal Isotropic Finishing Operations Videos

Additional Part Applications

This slideshow requires JavaScript.

Further reading:  Internet resources

(1)  “Isotropic Mass Finishing for Surface Integrity and Part Performance”,  Article From: Products Finishing, Jack Clark, from Surface Analytics, LLC and David Davidson, from SME Deburr/Finish Technical Group, Posted on: 1/1/2015, [Barrel, vibratory, centrifugal and spindle finish can improve part performance and service life.]  http://www.pfonline.com/articles/isotropic-mass-finishing-for-surface-integrity-and-part-performance

(2)  “Turbo-Charged Abrasive Machining Offers Uniformity, Consistency”  Article From: Products Finishing, by: Dr. Michael Massarsky, President from Turbo-Finish Corporation, and David A. Davidson, from SME Deburr/Finish Technical Group.  Posted on: 6/1/2012.  [Method can deburr, produce edge contour effects rapidly]  http://www.pfonline.com/articles/turbo-charged-abrasive-machining-offers-uniformity-consistency

(3)  “Turbo-Abrasive Machining and Finishing”. MANUFACTURING ENGINEERING – Aerospace Supplement, by: Dr. Michael Massarsky, President from Turbo-Finish Corporation, and David A. Davidson, from SME Deburr/Finish Technical Group. [Method first developed for the aerospace industry can improve surface integrity and part performance]  http://www.slideshare.net/dryfinish/turboabrasive-machining-me-aerospace-supplement-reprint

(4)  “The Role of Surface Finish in Improving Part Performnce”, MANUFACTURING ENGINEERING, by Jack Clark, Surface Analytics.com and David A. Davidson, from SME Deburr/Finish Technical Group.
http://www.slideshare.net/dryfinish/november-2012-f4-deburring-1-final

(5)  “Free Abrasives Flow for Automated Finishing”, MANUFACTURING ENGINEERING, , by: Dr. Michael Massarsky, President from Turbo-Finish Corporation, and David A. Davidson, from SME Deburr/Finish Technical Group. [Exciting new methods of surface finishing that go beyond deburring to specific isotropic surface finishes that can increase service life]  http://www.slideshare.net/dryfinish/october-2013-f2-deburring-1

(6) Turbo-Abrasive Machining Demonstration Video:  https://www.youtube.com/watch?v=jYxqCxMIHNo

(7) SME Spokane, WA Factory Floor video, Centrifugal Finishing in the Precision Machine Shop: Demonstration)  https://www.youtube.com/watch?v=dUdKjaysTYM

 

AUTHOR BIOGRAPHY –  David A. Davidson, [dryfinish@gmail.com]

Mr. Davidson is a deburring/surface finishing specialist and consultant.  He has contributed technical articles to Metal Finishing and other technical and trade publications and is the author of the Mass Finishing section in the current Metal Finishing Guidebook and Directory.  He has also written and lectured extensively for the Society  of Manufacturing Engineers, Society of Plastics Engineers, American Electroplaters and Surface Finishers Association and the Mass Finishing Job Shops Association.  Mr. Davidson’s specialty is finishing process and finishing product development.

Below:  Slide deck from SME Webinar on Centrifugal Isotopic Finishing. by Jack Clark and Dave Davidson

This slideshow requires JavaScript.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s